1.) Assemble the following items. These are the only items you will need to produce any finished Sterold

product:

-Corrier oil
– Syringe (Any size)
– Benzyl Benzoate (BB)
– Benzgl Alcohol (BA)
– Sterile Glass Vial (Any size)
– Needles
– Thermometer
– High Quality Steroid Pow der
– Sterile Syringe filter .22um
– Digital scalcs measuring to o.019

It is important to have everything you will need at hand, the best way to cook is to do everything quickly. This prevents fluctuations in temperature and excessive oxidation of your compounds – both allow the compound to reach its strengt potential and many ‘cooks’ do not allow for this. Set up your water bath by boiling the kettle and adding a 2-3cm of the boiling water into the base of a pan, or similar container – work quickly from this point so the water temperature does not drop by too much. 150f is ideal for the temperature of this water but it is not greatly important.

2.) Select the recipe from our Recipes Page. Forum or create your own with our Steroid Calculator and scale the recipe up or down depending on the weight of pow der you are using, For exam ple if the recipe is for 10g and you have only 5g of pow der you will halve all the values.

The“Recipe” is simply the lowest amount of solvents (BA 8B) required to keep the powders dissolved ·2% BA and 20% BB you will find can hold almost all compounds in their normal Mgl mL variations.

Stronger solvents like Ethyl Oleate are often used by Steroid labs to make high Mgl ml prodvcts or with products that tend fo be more painful.

ln this example we will be using the following Trenbolone Acetate Recipe;
50mlTren Acetate 5g Tren Acetate pow der
1ml BA
10ml BB
35ml Grape-seed oil

Weigh the Steroid pow der into the Glass Beaker as shown above. Add the Benzyl Alcohol and Benzyl Benzoate

3.) The solvnts will begin immediately dissolvng the powder but in order to speed the process upit is possible to use o Water Bath

Pace the vial into a few cm of water in a pan or something similar: It is important nof to use water that istoo hot because this will cause some products to oxidize -15of is o good temperature to use. alternativelyboiled woter from the kettle. The Corrier Oi should be the same temperoture as the solution when it isadded so if you warm the solution in a woter bath you should also do the same to the Carier Oil

The objecive ot this point issimplyto fuly dissolve the povder into the Solvents There should be no”Hormone swirls’ or ony visible powder remaining in the solution and once this is acheived move on tothe next step

4.) Add the warmed the Grope Seed Oilto the solution. this case 35mlmust be added. Mix thoroughly.again. there should be no Hormone Swirls – once this occurs remove immediately from the water bathand move on to the Filtering process.

Above: The Steroid Powder is fully dissolved in the Solvents. the Carrier Oilis added and the product is ready to bo filtored

5.) Drow up the Solution into the Syringe you wil be fitering with.this can bea single large syringeor this can be repeated multiple times with a smaller Syringe. Remove the 0.22um Sterile SyringeFilter from its packaging and far the green needle to the smaller side and then apply to the syringe. Forassistance on the best type of Syringe Fiters please Contact Taigui customer senvice

wipe the top of the Sterile Vial with an Aicohol swab and insert the Green Needie init. put the needleattached to the suringe fiter into the vial as shown below:

You have now successfully completed the process of producing Hormones. It is a very straight forward process and requires no expertise. In this example 50ml of Trenbolone Acetate

The entire process above has taken roughly 4o minutes and has required zero skil In this example 50mlofTrenbolone Acetate. with a street value of roughly $747 was producedwith a total production cost of roughly s100-an exceptional profit/savng margin